Shaft Kit Motor

3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave

3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave

3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave    3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave
3 PCS Nema 34 stepper motor with 3.5A 1600oz-in for Dual sha ft. 3 PCS DQ860MA Stepper Driver with 80VDC, 7.8A, 256 Microstep.

3 PCS Power Supply for. 2, Stepper Motor Driver DQ860MA. The DQ860MA is an economical microstepping driver based on patented technology of Wantai Motor.

It is suitable for driving 2-phase 4-phase hybrid stepping motors. By using the advanced bipolar constant-current shopping technique , it can output more speed and torque from the same motor, compared with traditional drivers , such as L/R drivers. Its 3-state current control technology allows coil currents to be well controlled and with relatively small current ripple, therefore less motor heating is achieved. Low cost and good high-speed torque. Supply voltage up to +80VD.

Suitable for-2-phase and 4-phase motors. Output current up to 7.8A, 5.6A rated current.

Dip switch current setting 8different values. Pulse frequency up to 200KHz. Small size (1079748), Weight:0.6KG. 3, Power Supply -350W , 60VDC, 5.9A.

500Hz, 2G 10min, /11cycle, 60min, each axes. I/P-O/P:3KVACI/P-FG:1.5KVACI/P-FG:0.5KVAC. Set pins according to software as follows.

Output pin: P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17. P2 X axis Pulse, P3 X axis Direction.

P4 Y axis Pulse, P5 - Y axis Direction. P6 Z axis Pulse, P7 Z axis Direction.

P8 - A axis Pulse, P9 - A axis Direction. P14 - B axis Pulse, P1- B axis Direction. P16 - C axis Pulse, P17- C axis Direction. Input pin: P10 , P11, P12, P13, P15.

Set them for Emergency Stop and X Y Z Limit switch. More order quantities, more discount!! Our products are mainly used in robotization, Spinning Automatization, Printing, Packing, Medica Machine, Make-up Equipment, Household Appliance, Milling Machine, Engraver Machine, CNC Routers and so on, automatic equipment of various trades. The item "3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave" is in sale since Thursday, October 23, 2014.

This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Electric Motors\Stepper Motors". The seller is "wantmotor2013" and is located in Rowland Heights, California. This item can be shipped worldwide.

  • Driver/Controller Bundle: Motor with Driver & Controller Board
  • Model: 85BYGH450C-012B
  • Country/Region of Manufacture: China
  • Current Type: DC
  • Wiring Configuration: 4-Wire Bipolar
  • MPN: Does Not Apply
  • Full Step Angle: 1.8° (200 Steps)
  • Holding Torque: 1600oz-in
  • Brand: WANTAI
  • Base RPM: 500-800


3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave    3Axis Nema34 Stepper Motor 1600oz-in 3.5A Dual Shaft&Driver 7.8A CNC kit engrave