Shaft Kit Motor

Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC

Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC
Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC
Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC
Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC
Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC
Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC

Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC   Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC

1PC Nema 34 Stepper Motor with Dual shafts 1600oz-in holding torque, 3.5A, 151mm. 2PCS Nema 23 Stepper Motor with Dual shafts 425oz-in Holding torque. 1PC Stepper Driver DQ860MA with 7.8A. 2PCS Stepper Driver DQ542MA With 4.2A Peak current.

1PC Power Suuply 350W 36V. 1PC Power Suuply 350W 60V. 1PC Breakout Board&1PC DB25 Cable. Feel free to contact me for any question! DQ860MA is a type of two-phase hybrid stepping motor driver, the drive voltage of it is from 24VDC to 80VDC.

It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter and less than 7.8A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Holding torque when DQ860MA run under high speed is also significantly higher than the other two-phase driver, whats more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on.

Average current control, 2-phase sinusoidal output current drive. Supply voltage from 24VDC to 80VDC. Overvoltage, under voltage, overcurrent, phase short circuit protectio. 14 channels subdivision and automatic idle-current reductio. 8 channels output phase current setting.

Motor torque is related to speed, but not related to step/revolution. High hording torque under high spe. No condensation, no water droplets.

Prohibition of combustible gases and conductive dust. DQ542MA is a type of two-phase hybrid stepping motor driver, the drive voltage of it is from 18VDC to 50VDC.

It is designed for use with 2-phase hybrid stepper motor of all kinds with 42mm to 86mm outside diameter and less than 4.0A phase current. This circuit that it adopts is smiliar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Holding torque when DQ542MA run under high speed is also significantly higher than the other two-phase driver, whats more, the positioning accuracy is also higher.

Supply voltage from 18VDC to 50VDC. 15 channels subdivision and automatic idle-current reductio. 350W Single Output Switching Power Supply. AC input range selected by switch.

Protections:short circuit/overload/over voltage/over temperature. 100% full load burn-in test. AC input voltage range: 90. AC inrush current: cold start 25A/115V, 50A/230V. DC adjustment range:±10% rated output voltage. 135%, hiccup mode, auto recovery. Setup, rise, hold up time: 200ms, 50ms, 20ms/230VAC at full load.

Working temperature and humidity:-10. Set pins according to software as follows. Output pin: P1, P2, P3, P4, P5, P6, P7, P8, P9, P14, P16, P17.

X axis Pulse, P3 X axis Direction. Y axis Pulse, P5 - Y axis Direction. Z axis Pulse, P7 Z axis Direction. A axis Pulse, P9 - A axis Direction. B axis Pulse, P1- B axis Direction.

C axis Pulse, P17- C axis Direction. Them for Emergency Stop and X Y.

Please give us the opportunity to resolve any problem when you have, we will try our best to help you. If you are not satisfied with the package, please tell us the reason. Changzhou Wantai Electrical Appliance Co. Ltd has powerful technology, mature technics and complete testing equipment. And we have obtained ISO9001:2000 certification, CE certification and all of our products conform to RoHS requirements.

We can manufacture products according to our customer's requirements. Our product are mainly used in Aerospace & Defense, Automation Applications, Commercial Equipment, Industrial Tool, Medical Device & Equipment, Medical Mobility, Printing & Imaging, Pump, Semiconductor Equipment, Vehicle, , Milling Machine, Engraver Machine, CNC Routers Applications, etc. 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC" is in sale since Friday, August 24, 2018. This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives".

The seller is "wantmotor1207" and is located in Rowland Heights, California. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Canada, Mexico, Brazil, Australia.
  • Model: 85BYGH450C-012B&57BYGH115-003B
  • MPN: Does Not Apply
  • Brand: Unbranded/Generic
  • Country of Manufacture: China

Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC   Hot selling! 3 Axis Kit 425oz&1600oz-in Step Motor Dual Shaft &Driver Wantai CNC